Product Care

Atlantis shower systems are the cutting edge of design with clean lines and minimal fall in the shower base. We recommend after showering any residual water either on the shower base or surface splashes outside the shower be wiped down.

There are many bathroom cleaning products available on the market. Atlantis has not tested all of these products, however cleaners containing Non-Ionic and Cationic Surfactants and Citric Acids should be avoided. Due to chemicals in cleaning products regularly changing, Atlantis does not promote the use of specific brands other than our CristalCote Glass Treatment System. Many bathroom products may be suitable for cleaning however we do recommend you read instructions on each product and carry out a test in a small inconspicuous area, prior to cleaning the entire surface.

Cristal Cote is a protective nano-coating that has been factory-applied to Atlantis CristalVision Glass (2120 & 2030mm high) and does not require the use of harsh chemicals.

Glass should be wiped/squeegeed down after every use. Using a damp microfibre cloth and mild detergent, simply wipe down glass screens to remove any soap scum and grime. Do not use any rough gritty, highly acidic, alkaline or abrasive cleansers such as Jif, Ajax or cerium oxide as they may damage the coating.

Some areas that have water spotting due to high mineral concentration, a little extra care may be required to avoid deposit build up on the coating. A solution of white vinegar (1 part vinegar to 1 part water) should be sprayed on the glass and allowed to soak for several minutes. This will dissolve any mineral deposits that have built up on the glass surface. A damp microfiber cloth should then be used to wipe over the glass. This method is not suitable for acrylic surfaces. Alternatively we recommend using CristalCote Glass Cleanser & Protector to maintain an as new finish.

Standard Glass (1930mm high) is not treated in any way and should be wiped/squeegeed down after every use. We recommend using CristalCote Glass Cleanser & Protector to maintain an as new finish on this glass. 

LiberettoStone is a mix of resin and fine stone properties that is cast and polished to create beautiful bathroom pieces. The Ebony & Ivory collection is a handmade product which has the benefits of stone – easy-to-clean and unparalleled strength. Due to the manufacturing process and the nature of cast stone the polished surface of a black shower base may appear uneven (white shower bases do not reflect light in the same way), this is normal. While being durable, LiberettoStone is polish-able in order to remove any small imperfections that may occur during everyday use.

For everyday cleaning after use, simply wipe with a soft wet cloth to remove any surface dirt. Your shower base may occasionally require a mildly abrasive product to erase stubborn marks (Autosol is widely available at Repco, SuperCheap and Mitre 10). Never use petroleum-based products when cleaning. eg. paint thinners or other solvents, as they may damage the solid surface. Please note some popular bathroom cleaners can adversely affect the surface, contact Atlantis if you have questions regarding a specific cleaner.

In the unlikely event that your shower base is scratched during the handling or installation. Polishing the shower tray will remove any light scratches or imperfections in the surface. For surface scratches it is recommended that the base be sanded, start by using 800 grit sandpaper, gradually change your grades of sandpaper. Then 1200, 1500, 2000 finishing with a G3 polishing compound. Deeper scratches start sanding the surface with a 400 grit, 600, 800, 1000, 12000, 1500, 2000 grit sandpaper, finish off using G3 polishing compound. If you do not have access to a buffing wheel, hand polish with a microfibre cloth for minor imperfections.

If you do have a question regarding the surface of your LiberettoStone contact Atlantis and the technical team will be able to discuss this with you.

Hinges, Handles and Rollers should be wiped down after every use with a towel to thoroughly dry. If the hardware is kept clean after every use, it will not collect mineral deposits that require the use of a soap solution. Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to dry metal, not an abrasive rubbing action. If you are unable to dry the hardware after every use, a weekly cleaning is suggested. The correct method to be used in cleaning the hardware is a mild soap and warm water mixture. Using a soft microfibre cloth, proceed to clean the hardware. After you’ve cleaned the hardware, rinse thoroughly with clean warm water and dry. Never use abrasive cleaners, scrapers or pads. If for some reason any components become loose, grub screws may be hand tightened using the appropriate size hex key. Take care not to strip the thread or damage the head. This could result in no further possible adjustment.

Foundry Series Hardware

The Brass Finishes in the Foundry Series range is 100% natural Brass that is not coated or waxed. This means that both Polished Brass and Aged Brass components will patina with use over time, depending on the unique conditions of your bathroom. Brass products should be cleaned with a soft microfibre cloth, mild soap and water mixture. If required, Brasso may be used to return brass to it’s polished finish. All other hardware including Matte Black, Gunmetal, Brushed Nickel and Brushed Gold should also be cleaned using a soft microfibre cloth, mild soap and water mixture. DO NOT use any cleaning products designed to remove tarnish or rust, abrasive bleach or scouring pads. Doing so may adversely affect the surface finish.

Shower bases, Wall Liners and prefinished EasyNiches

We recommend towel drying acrylic products after each use to remove any contaminants. Additionally, on a weekly basis use a damp microfibre cloth and mild detergent simply wipe down to remove any soap scum and grime.

Remove waste top, basket and hair catcher if applicable. Clean all associated body parts of hair, soap scum, body fats and mineral deposits. DO NOT pour boiling water down the drain as it may melt components of the drain.

Note: On AquaPlane Wastes (oval shape) please use the tool provided to remove the waste fin to clean the waste. DO NOT remove any bolts that hold the waste together.